View 715P_396747.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
Type 715P
Vishay Sprague
Polypropylene Film Capacitors ORANGE DROP(R), Low Loss
Polypropylene plastic film is employed as the dielectric in Type 715P ORANGE DROP(R) capacitors. Type 715P capacitors are ideal for applications where high AC current flow is found, as in certain solid-state TV vertical circuits, r-f generators and pulse-forming networks where dielectric heating is often a problem. The polypropylene dielectric film is similar to polystyrene in that it can handle high AC currents due to its low loss but with the added advantage of an operating temperature to + 105C. Capacitance change with temperature is less than 3% over the entire operating temperature range. The temperature coefficient is negative and virtually linear at 180PPM/C over the temperature range of + 25C to + 105C. This characteristic means the Type 715P is suitable for matching with positive TC resistors and inductors to maintain circuit stability. Type 715P ORANGE DROP(R) capacitors are conformally coated with a flame retardant epoxy. Performance characteristics, as well as curves showing typical variation in electrical characteristics as a function of temperature and frequency, are given.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55C to + 85C standard; up to + 105C when working voltage is reduced to 50% of the + 85C rating. Insulation Resistance: After a 2 minute charge at rated voltage or 500 V, whichever is less. At + 25C: 400,000 Megohm for C .5F. 200,000 Megohm - Microfarads for C > .5 Microfarads. At + 85C: 20,000 Megohm for C .5 Microfarads. 10,000 Megohm - Microfarads for C > .5 Microfarads. At + 105C: 2000 Megohm for C .5F. 1000 Megohm - Microfarads for C > .5 Microfarads. Capacitance, Tolerance and Dissipation Factor: Capacitors shall be measured at a frequency of 1000Hz at + 25C or else be referred to measurements made at that frequency and temperature. The maximum dissipation factor shall be 0.1%. Dielectric Withstanding Voltage: Capacitors rated below 1000 volts shall withstand a DC potential of 250% of rated voltage applied between terminals for not more than 5 seconds. Capacitors rated 1000 volts and above shall withstand a DC potential of 200% of rated voltage applied between the terminals for not more than 5 seconds. The test voltage must be applied and discharged through a resistor of one ohm per volt. Humidity Test: Condition capacitors with no voltage applied for 72 hours at 95% relative humidity and + 75C. Remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure insulation resistance after a two minute charge at + 25C and rated voltage or 500 VDC, whichever is less. Minimum product of insulation resistance and capacitance shall be 50,000 Megohm-microfarads after test but need not exceed 100,000 Megohm. Not more than one failure in 12 units tested shall be permitted. DC Life Test: Capacitors are capable of withstanding a 500 hour life test at + 85C at 150% of rated working voltage. After test, capacitance shall not have changed by more than 5% of initial value, insulation resistance shall not have decreased by more than 50% of the initial limit and dissipation factor shall not have increased to more than 0.1%. AC Life Test: Capacitors shall withstand the maximum 60Hz voltage for a period of 500 hours at + 85C.
Rated DC Voltage 200 400, 600 800, 1200, 1600 Maximum 60Hz Voltage 155 200 500
Not more than one failure allowed in 12 units tested.
Document Number: 42018 Revision 13-Nov-03
For technical questions, contact spresale@vishay.com
www.vishay.com 47
Type 715P
Vishay Sprague
DIMENSIONS in inches [millimeters]
L Max. L Max. L Max. D Max.
0.250 [6.350] Max. 1.250 [31.750] Min. Lead Length
0.250 [6.350] Max. Lead Length
0.250 [6.350] Max.
0.032 [0.813] Dia. (No. 20 AWG) Tinned Copper-Clad Steel
S
S
S
Terminal A
CASE CODE J K L M L (Max.) 0.75 [19.050] 0.95 [24.130] 1.30 [33.020] 1.70 [43.180]
Terminal B
Terminal A 0.060 [1.524] 0.500 [12.700] 0.688 [17.475] 1.031 [26.187] 1.406 [35.712]
Terminal D
S Terminal B 0.030 [0.762] 0.500 [12.700] 0.688 [17.475] 0.969 [24.613] 1.344 [34.138] Terminal D
0.030 [0.762]
0.375 [9.525] 0.375 [9.525] 0.719 [18.263] 1.094 [27.788]
PERFORMANCE CHARACTERISTICS
PERCENT CAPACITANCE CHANGE - 1000Hz
+2 +1 0 5 -1 -2 - 55 - 50 TYPICAL 2 10-2
TAN
- 25
0
+ 25
+ 50
+ 85 + 105 + 125 + 75 + 100
10-3 5
PERCENT DISSIPATION FACTOR - 1000Hz
TEMPERATURE DEG. CENTIGRADE
0.075 0.05 0.025 0 - 55 - 50 TYPICAL 2 10-4 1 - 25 0 + 25 + 50 + 85 + 105 + 125 + 75 + 100 1000 5 200
.0 39
TYPICAL
2
5
10
2
5
100
2
5
1000
TEMPERATURE DEG. CENTIGRADE
TEMPERATURE DEG. CENTIGRADE 1000 5 2 155 100 5
VOLTS - rms
VOLTS - rms
.0
.0 .0 .4 7 F
200 V
03
12
82
F
.0 39
100 5
9 F
F
F
F 7 .2
.4 7 F
.0
F
2 10 400 V
.1 8 F
18
F
2
10 1 2 5 10 2 5 100 2 5 1000 FREQUENCY - kHz
1
2
5
10
2
5
100
2
5
1000
FREQUENCY - kHz
www.vishay.com 48
For technical questions, contact spresale@vishay.com
Document Number: 42018 Revision 13-Nov-03
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1000 5
0 .0
1000 450
.0
VOLTS - rms
VOLTS - rms
200
.0
200 100
56
F
.0
F 1
100 5 2 10 1 1000 475 2 5 10 2
.2 2 F
27
18
F
.1 2 F
.0
F
08
.0
2 F
.1
5
05
F
3 .0
6 F
F 3
600 V
2 10 5 100 2 5 1000 1000 500 1 2
800 V
5
10
2
5
100
2
5
1000
FREQUENCY - kHz
FREQUENCY - kHz
.0
.0
2
27
02
.0
F
.0
.0
47
7 F
2
.0
VOLTS - rms
33
01
VOLTS - rms
08
F
2 F
.0 1 F
8 F
.0 05
.0
100 5 2 10 1 2 5 10 2 5
F
03
.0
9 F
100
6 F
15
.0
5 2
F
18
F
1200 V 10 100 2 5 1000 1
1600 V
2
5
10
2
5
100
2
5
1000
FREQUENCY - kHz
FREQUENCY - kHz
STANDARD RATINGS* in inches [millimeters]
10% TOLERANCE
.012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .1 .12 .15 .18 .22 .27 .33 .39 .47
F
SIZE PART NUMBER 200 VDC/155 VAC** 715P12392J 715P15392J 715P18392J 715P22392J 715P27392J 715P33392J 715P39392K 715P47392K 715P56392K 715P68392K 715P82392L 715P10492L 715P12492L 715P15492L 715P18492L 715P22492L 715P27492M 715P33492M 715P39492M 715P47492M 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 0.37 [9.40] 0.37 [9.40] 0.37 [9.40] 0.37 [9.40] 0.42 [10.67] 0.42 [10.67] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.55 [13.97] 0.55 [13.97] 0.62 [15.75] 0.62 [15.75] 0.65 [16.51] 0.65 [16.51] 0.75 [19.05] 0.75 [19.05] L D
* Shaded items, when ordered as 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60Hz rms. Document Number: 42018 Revision 13-Nov-03 For technical questions, contact spresale@vishay.com www.vishay.com 49
Type 715P
Vishay Sprague
STANDARD RATINGS* in inches [millimeters]
F 10% TOLERANCE
.0039 .0047 .0056 .0068 .0082 .01 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .1 .12 .15 .18 .22 .27 .33 .39 .47 SIZE PART NUMBER 400 VDC/200 VAC** 715P39294J 715P47294J 715P56294J 715P68294J 715P82294J 715P10394J 715P12394J 715P15394J 715P18394K 715P22394K 715P27394K 715P33394K 715P39394L 715P47394L 715P56394L 715P68394L 715P82394L 715P10494L 715P12494L 715P15494L 715P18494M 715P22494M 715P27494M 715P33494M 715P39494M 715P47494M L 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] Dia. 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.90 [22.86] 0.90 [22.86]
600 VDC/200 VAC** 0.75 [19.05] .001 0.40 [10.16] 715P10296J 0.75 [19.05] .0012 0.40 [10.16] 715P12296J 0.75 [19.05] .0015 715P15296J 0.40 [10.16] 0.75 [19.05] .0018 715P18296J 0.40 [10.16] 0.75 [19.05] .0022 715P22296J 0.40 [10.16] 0.75 [19.05] .0027 715P27296J 0.40 [10.16] 0.75 [19.05] .0033 715P33296J 0.40 [10.16] 0.75 [19.05] .0039 715P39296J 0.45 [11.43] 0.75 [19.05] .0047 715P47296J 0.45 [11.43] 0.75 [19.05] .0056 715P56296J 0.45 [11.43] .0068 0.75 [19.05] 715P68296J 0.45 [11.43] 0.95 [24.13] .0082 715P82296K 0.45 [11.43] 0.95 [24.13] .01 715P10396K 0.45 [11.43] .012 0.95 [24.13] 715P12396K 0.50 [12.70] 0.95 [24.13] .015 715P15396K 0.50 [12.70] .018 0.95 [24.13] 715P18396K 0.55 [13.97] 0.95 [24.13] .022 715P22396K 0.55 [13.97] 1.30 [33.02] .027 715P27396L 0.55 [13.97] 1.30 [33.02] .033 715P33396L 0.55 [13.97] 1.30 [33.02] .039 715P39396L 0.60 [15.24] 1.30 [33.02] .047 715P47396L 0.60 [15.24] 1.30 [33.02] .056 715P56396L 0.65 [16.51] 1.30 [33.02] .068 715P68396L 0.65 [16.51] 1.30 [33.02] .082 715P82396L 0.75 [19.05] .1 1.30 [33.02] 715P10496L 0.75 [19.05] 1.70 [43.18] .12 715P12496M 0.75 [19.05] .15 1.70 [43.18] 715P15496M 0.75 [19.05] 1.70 [43.18] .18 715P18496M 0.85 [21.59] .22 1.70 [43.18] 715P22496M 0.85 [21.59] * Shaded items, when ordered as 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60Hz rms. www.vishay.com 50 For technical questions, contact spresale@vishay.com Document Number: 42018 Revision 13-Nov-03
Type 715P
Vishay Sprague
STANDARD RATINGS* in inches [millimeters]
F 10% TOLERANCE
.0056 .0068 .0082 .01 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .1 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .01 .012 .015 .018 .022 .027 .033 .039 .047 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .01 .012 .015 .018 .022 .027 .033 SIZE PART NUMBER 800 VDC/450 VAC** 715P56298L 715P68298L 715P82298L 715P10398L 715P12398L 715P15398L 715P18398L 715P22398L 715P27398L 715P33398L 715P39398M 715P47398M 715P56398M 715P68398M 715P82398M 715P10498M 1200 VDC/475 VAC** 715P272912L 715P332912L 715P392912L 715P472912L 715P562912L 715P682912L 715P822912L 715P103912L 715P123912L 715P153912L 715P183912M 715P223912M 715P273912M 715P333912M 715P393912M 715P473912M 1600 VDC/500 VAC** 715P182916L 715P222916L 715P272916L 715P332916L 715P392916L 715P472916L 715P562916L 715P682916L 715P822916L 715P103916L 715P123916M 715P153916M 715P183916M 715P223916M 715P273916M 715P333916M L 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] D 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.90 [22.86] 0.90 [22.86] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.65 [16.51] 0.65 [16.51] 0.75 [19.05] 0.75 [19.05] 0.85 [21.59] 0.85 [21.59] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.70 [17.78] 0.70 [17.78] 0.75 [19.05] 0.75 [19.05] 0.85 [21.59] 0.85 [21.59] 0.95 [24.13] 0.95 [24.13]
* Shaded items, when ordered as 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60Hz rms. Document Number: 42018 Revision 13-Nov-03 For technical questions, contact spresale@vishay.com www.vishay.com 51
Type 715P
Vishay Sprague
STANDARD MARKING FORMAT
SAMPLE MARKING 715P200 V 1239 9340 715P 200 V 1239 9940
DESCRIPTION Sprague(R) Identification Type Number DC Voltage Rating, Volts Capacitance and Tolerance Code Weekly Date Code (i.e. 40th week for 1999)
TOLERANCE CODES PER EIA STANDARDS 9 = 10% 5 = 5% 2 = 2%
ORDERING INFORMATION
715P TYPE
123 CAPACITANCE
9 TOLERANCE
2 DC VOLTAGE RATING @ + 85C
J CASE CODE
D TERMINAL
3 LEAD LENGTH
This is expressed in picofarads. The first two digits are significant. The third is the number of zeros to follow. Values must conform to decade rating for the tolerance specified.
9 = 10% 5 = 5% 2 = 2%
This is expressed in hundreds of volts. Example: 715P R5 = 50 volts.
See Dimensional Configurations.
A = Straight lead. B = Hairpin crimped. D = Hockey crimped.
1 = 0.187" 0.030" [4.750 0.762] 2 = 0.250" 0.030" [6.350 0.762] 3 = 1.250" [31.750] Minimum
www.vishay.com 52
For technical questions, contact spresale@vishay.com
Document Number: 42018 Revision 13-Nov-03
Legal Disclaimer Notice
Vishay
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000 Revision: 08-Apr-05
www.vishay.com 1

▲Up To Search▲

Price & Availability of 715P

	To Download 715P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .